March 29, 2024, 12:14:21 am
Welcome, Guest. Please login or register
News:

Arturia Forums



Author Topic: Road Case for Minibrute?  (Read 24390 times)

Ollie Stench

  • Apprentice
  • Apprentice
  • *
  • Posts: 9
  • Karma: 0
Road Case for Minibrute?
« on: July 17, 2012, 03:04:25 am »
Anyone have any recommendations for an Anvil-style road case for the Minibrute?

17hex

  • Apprentice
  • Apprentice
  • *
  • Posts: 6
  • Karma: 0
Re: Road Case for Minibrute?
« Reply #1 on: July 23, 2012, 06:05:05 pm »
Hi Ollie

It's Jason (from Kether) :)  I'm using a metal ATA foam padded briefcase for mine.. i haven't tried but i'm pretty sure it'd pass customs, and its at least as well padded as any other synth case i have. 

Here's one from the UK if you dont mind shipping and VAT.. ;-)
http://www.maplin.co.uk/flight-case-with-foam-36796


I hope it helps, and nice to "see" you.

Ollie Stench

  • Apprentice
  • Apprentice
  • *
  • Posts: 9
  • Karma: 0
Re: Road Case for Minibrute?
« Reply #2 on: July 29, 2012, 09:06:33 pm »
I have one of those that I bought from Menards and its not quite wide enough. I'll have to check your link closely and report back.

The01Habiitat

  • Apprentice
  • Apprentice
  • *
  • Posts: 24
  • Karma: -1
Re: Road Case for Minibrute?
« Reply #3 on: September 13, 2012, 07:03:32 am »
Hi Ollie


Here's one from the UK if you dont mind shipping and VAT.. ;-)
http://www.maplin.co.uk/flight-case-with-foam-36796



you have this case? youre sure it fits a minibrute?

washburn

  • Apprentice
  • Apprentice
  • *
  • Posts: 17
  • Karma: 0
Re: Road Case for Minibrute?
« Reply #4 on: September 13, 2012, 04:05:25 pm »
check out this company for custom cases
http://www.novaforge.com.au/

Ollie Stench

  • Apprentice
  • Apprentice
  • *
  • Posts: 9
  • Karma: 0
Re: Road Case for Minibrute?
« Reply #5 on: September 30, 2012, 03:42:39 am »
I made my own with an equipment case from a surplus store and styrofoam and foam rubber. I will post pix when I can.

UMCorps

  • Apprentice
  • Apprentice
  • *
  • Posts: 7
  • Karma: 0
Re: Road Case for Minibrute?
« Reply #6 on: October 01, 2012, 03:13:51 pm »

Ollie Stench

  • Apprentice
  • Apprentice
  • *
  • Posts: 9
  • Karma: 0
Re: Road Case for Minibrute?
« Reply #7 on: October 21, 2012, 10:53:41 pm »


Here's the road case I made. I bought the case and foam from Axman Surplus in St. Paul, Minnesota. I built up under and around the foam with styrofoam and hot-glued it all in place. I left room for cords, effects, headphones, etc on the side. The Minibrute is a tight fit, but it's not going anywhere.  Total cost was less than $25 and about 4 hours of my time (spread out over the course of a week).

rafar

  • Newbie
  • *
  • Posts: 1
  • Karma: 0
    • live
Re: Road Case for Minibrute?
« Reply #8 on: November 02, 2012, 01:57:33 am »
Nice job with the case!

Paf

  • Apprentice
  • Apprentice
  • *
  • Posts: 5
  • Karma: 0
Re: Road Case for Minibrute?
« Reply #9 on: May 02, 2013, 08:04:06 pm »
I made use of an old plastic suitcase:





tertior

  • Full Member
  • ***
  • Posts: 169
  • Karma: 7
Re: Road Case for Minibrute?
« Reply #10 on: May 03, 2013, 08:43:29 am »

Steve Satori

  • Newbie
  • *
  • Posts: 1
  • Karma: 0
Re: Road Case for Minibrute?
« Reply #11 on: May 15, 2013, 04:29:17 pm »
I just bought the Gator G-Mix-B 1515 Mixerbag, and it fit's like a glove! Has extra compartments and it's cheap too.

http://www.thomann.de/gb/gator_gmixb_1515.htm

MarctheDarc

  • Apprentice
  • Apprentice
  • *
  • Posts: 36
  • Karma: 4
Re: Road Case for Minibrute?
« Reply #12 on: May 17, 2013, 04:23:07 am »
Perfect and not expansive


http://www.thomann.de/fr/thomann_mix_case_4044x.htm

Could you by chance upload a picture showing the fit? It would be much appreciated.

tertior

  • Full Member
  • ***
  • Posts: 169
  • Karma: 7
Re: Road Case for Minibrute?
« Reply #13 on: May 17, 2013, 11:39:48 am »



the  foam is pre-cut, easy to do

MarctheDarc

  • Apprentice
  • Apprentice
  • *
  • Posts: 36
  • Karma: 4
Re: Road Case for Minibrute?
« Reply #14 on: May 17, 2013, 03:57:57 pm »
Looks reasonable. Thanks for the tip.
Hate to ask more, but do you per chance also have a picture with the unit in place?

 

Carbonate design by Bloc
SMF 2.0.17 | SMF © 2019, Simple Machines