Arturia - Resources

The chameleon controller and sequencer that provides nearly endless possibilities. With a compact format, it is the perfect companion on the road or in the studio.

US$129 - Buy Now

Or find a dealer near you

Downloads & manuals

BeatStep

FIRMWARE

Platform	Name	Date	Size	Version	Infos
Win 7+	New BeatStep Firmware	01-Feb-2016	10.9 Mb	1.2.0.3	BeatStep firmware V 1.2.0.3 New features: Preset Reset = Press RECALL+STOP. It returns all data except pad calibration to default Full Reset = Press RECALL+PLAY. It returns all data including pad calibration to default Improvements: Faster knob acceleration Better visualization of MIDI Channel on pad when the sequencer is running Bug fixes: MMC messages are now transmitted via Midi DIN OUT port After power-up, Stop and Play retain the previous settings No more freeze of MIDI sync when lots of MIDI messages are received V 1.1.0.0 New Features Provide additional settings locally. There is now a way to set up some parameters directly on the unit while in SEQ mode. Shift + Knob 1: set gate time (50%..99%) Shift + Knob 2: set swing (50%..75%) Shift + Knob 3: set legato mode (off/on/on reset) Transpose pads with Controller in CNTRL mode It's now possible to transpose pads in CNTRL mode, using Shift + big knob, on a +/-24 half steps range. Extend sequencer big knob transposition range Transposition range (big knob) has been extended from +/-12 to +/-24 half steps Bug Fixes Knob acceleration too slow Knobs are now accelerated properly when turned fast Default start up memory should be 1 At power up, sequence from memory #1 is recalled (previously, a default sequence was loaded) MIDI channel pad highlight in Controller mode. Pad back-lighting is now restored after channel setting and similar operations Stuck note in CV while switching CV channel while playing Changing CV channel while playing a sequence no longer produces stuck CV note RPN/NRPN fine mode not working RPN/NRPN fine mode now works as expected when activated with MIDI Control Center Big knob value update between CNTRL mode and SEQ mode Setting rate/transpose in SEQ mode no longer affects the volume setting internal position in CNTRL mode Bad handling of SPP (Song Position Pointer) message Fixed Song Position Pointer message handling (when EXT SYNC is active), leading to better compatibility with Maschine® Inverted MIDI Values for pads/encoders It's now possible to program a pad or knob with min value > max value (useful for pads in switched control mode)
10.8+	New BeatStep Firmware	01-Feb-2016	19.9 Mb	1.2.0.3	BeatStep firmware V 1.2.0.3 New features: Preset Reset = Press RECALL+STOP. It returns all data except pad calibration to default Full Reset = Press RECALL+PLAY. It returns all data including pad calibration to default Improvements: Faster knob acceleration Better visualization of MIDI Channel on pad when the sequencer is running Bug fixes: MMC messages are now transmitted via Midi DIN OUT port After power-up, Stop and Play retain the previous settings No more freeze of MIDI sync when lots of MIDI messages are received V 1.1.0.0 New Features Provide additional settings locally. There is now a way to set up some parameters directly on the unit while in SEQ mode. Shift + Knob 1: set gate time (50%..99%) Shift + Knob 2: set swing (50%..75%) Shift + Knob 3: set legato mode (off/on/on reset) Transpose pads with Controller in CNTRL mode It's now possible to transpose pads in CNTRL mode, using Shift + big knob, on a +/-24 half steps range. Extend sequencer big knob transposition range Transposition range (big knob) has been extended from +/-12 to +/-24 half steps Bug Fixes Knob acceleration too slow Knobs are now accelerated properly when turned fast Default start up memory should be 1 At power up, sequence from memory #1 is recalled (previously, a default sequence was loaded) MIDI channel pad highlight in Controller mode. Pad back-lighting is now restored after channel setting and similar operations Stuck note in CV while switching CV channel while playing Changing CV channel while playing a sequence no longer produces stuck CV note RPN/NRPN fine mode not working RPN/NRPN fine mode now works as expected when activated with MIDI Control Center Big knob value update between CNTRL mode and SEQ mode Setting rate/transpose in SEQ mode no longer affects the volume setting internal position in CNTRL mode Bad handling of SPP (Song Position Pointer) message Fixed Song Position Pointer message handling (when EXT SYNC is active), leading to better compatibility with Maschine® Inverted MIDI Values for pads/encoders It's now possible to program a pad or knob with min value > max value (useful for pads in switched control mode)
	New BeatStep Firmware	01-Feb-2016	89.9 Kb	1.2.0.3	BeatStep firmware V 1.2.0.3 New features: Preset Reset = Press RECALL+STOP. It returns all data except pad calibration to default Full Reset = Press RECALL+PLAY. It returns all data including pad calibration to default Improvements: Faster knob acceleration Better visualization of MIDI Channel on pad when the sequencer is running Bug fixes: MMC messages are now transmitted via Midi DIN OUT port After power-up, Stop and Play retain the previous settings No more freeze of MIDI sync when lots of MIDI messages are received V 1.1.0.0 New Features Provide additional settings locally. There is now a way to set up some parameters directly on the unit while in SEQ mode. Shift + Knob 1: set gate time (50%..99%) Shift + Knob 2: set swing (50%..75%) Shift + Knob 3: set legato mode (off/on/on reset) Transpose pads with Controller in CNTRL mode It's now possible to transpose pads in CNTRL mode, using Shift + big knob, on a +/-24 half steps range. Extend sequencer big knob transposition range Transposition range (big knob) has been extended from +/-12 to +/-24 half steps Bug Fixes Knob acceleration too slow Knobs are now accelerated properly when turned fast Default start up memory should be 1 At power up, sequence from memory #1 is recalled (previously, a default sequence was loaded) MIDI channel pad highlight in Controller mode. Pad back-lighting is now restored after channel setting and similar operations Stuck note in CV while switching CV channel while playing Changing CV channel while playing a sequence no longer produces stuck CV note RPN/NRPN fine mode not working RPN/NRPN fine mode now works as expected when activated with MIDI Control Center Big knob value update between CNTRL mode and SEQ mode Setting rate/transpose in SEQ mode no longer affects the volume setting internal position in CNTRL mode Bad handling of SPP (Song Position Pointer) message Fixed Song Position Pointer message handling (when EXT SYNC is active), leading to better compatibility with Maschine® Inverted MIDI Values for pads/encoders It's now possible to program a pad or knob with min value > max value (useful for pads in switched control mode)
10.7+	BeatStep Firmware	16-Jun-2014	11.6 Mb	1.1	BeatStep firmware V 1.1.0.0 New Features Provide additional settings locally. There is now a way to set up some parameters directly on the unit while in SEQ mode. Shift + Knob 1: set gate time (50%..99%) Shift + Knob 2: set swing (50%..75%) Shift + Knob 3: set legato mode (off/on/on reset) Transpose pads with Controller in CNTRL mode It's now possible to transpose pads in CNTRL mode, using Shift + big knob, on a +/-24 half steps range. Extend sequencer big knob transposition range Transposition range (big knob) has been extended from +/-12 to +/-24 half steps Bug Fixes Knob acceleration too slow Knobs are now accelerated properly when turned fast Default start up memory should be 1 At power up, sequence from memory #1 is recalled (previously, a default sequence was loaded) MIDI channel pad highlight in Controller mode. Pad back-lighting is now restored after channel setting and similar operations Stuck note in CV while switching CV channel while playing Changing CV channel while playing a sequence no longer produces stuck CV note RPN/NRPN fine mode not working RPN/NRPN fine mode now works as expected when activated with MIDI Control Center Big knob value update between CNTRL mode and SEQ mode Setting rate/transpose in SEQ mode no longer affects the volume setting internal position in CNTRL mode Bad handling of SPP (Song Position Pointer) message Fixed Song Position Pointer message handling (when EXT SYNC is active), leading to better compatibility with Maschine® Inverted MIDI Values for pads/encoders It's now possible to program a pad or knob with min value > max value (useful for pads in switched control mode)
Win 7+	BeatStep Firmware	16-Jun-2014	8.4 Mb	1.1	BeatStep firmware V 1.1.0.0 New Features Provide additional settings locally. There is now a way to set up some parameters directly on the unit while in SEQ mode. Shift + Knob 1: set gate time (50%..99%) Shift + Knob 2: set swing (50%..75%) Shift + Knob 3: set legato mode (off/on/on reset) Transpose pads with Controller in CNTRL mode It's now possible to transpose pads in CNTRL mode, using Shift + big knob, on a +/-24 half steps range. Extend sequencer big knob transposition range Transposition range (big knob) has been extended from +/-12 to +/-24 half steps Bug Fixes Knob acceleration too slow Knobs are now accelerated properly when turned fast Default start up memory should be 1 At power up, sequence from memory #1 is recalled (previously, a default sequence was loaded) MIDI channel pad highlight in Controller mode. Pad back-lighting is now restored after channel setting and similar operations Stuck note in CV while switching CV channel while playing Changing CV channel while playing a sequence no longer produces stuck CV note RPN/NRPN fine mode not working RPN/NRPN fine mode now works as expected when activated with MIDI Control Center Big knob value update between CNTRL mode and SEQ mode Setting rate/transpose in SEQ mode no longer affects the volume setting internal position in CNTRL mode Bad handling of SPP (Song Position Pointer) message Fixed Song Position Pointer message handling (when EXT SYNC is active), leading to better compatibility with Maschine® Inverted MIDI Values for pads/encoders It's now possible to program a pad or knob with min value > max value (useful for pads in switched control mode)
10.7+	BeatStep Firmware	11-Mar-2014	11.6 Mb	1.0.1.4
Win 7+	BeatStep Firmware	11-Mar-2014	8.4 Mb	1.0.1.4
10.7+	BeatStep Firmware	18-Feb-2014	11.6 Mb	1.0.1
Win 7+	BeatStep Firmware	18-Feb-2014	8.4 Mb	1.0.1

MANUALS

Manual	Date	Size	Version
New BeatStep Spanish Manual	22-Oct-2014	2.3 Mb	1.0.1
New BeatStep English Manual	21-Jan-2014	725.7 Kb	1.0.1
New BeatStep French Manual	21-Jan-2014	758.4 Kb	1.0.1
New BeatStep Japanese Manual	21-Jan-2014	902.8 Kb	1.0.1

Midi Control Center

SOFTWARE

Platform	Name	Date	Size	Version	Infos
Win 7+	New Midi Control Center	16-Jan-2020	26.1 Mb	1.10.1.1411	MIDI Control Center V 1.10.1 New Features KeyLab Essential 88 integration Microfreak firmware 2.0.3 integration Added "Factory 2.0" presets bank for the Microfreak Added relative bend, scale, and root note settings for the Microfreak Updated embedded firmware versions for all products V 1.10.0 New Features Added MatrixBrute Factory 2.0 bank for MCC MatrixBrute 2.0 Firmware integration Catalina compatibility: Notarize macOs installer Added a modal popup when transfering preset or memories Improvements Various improvements for preset transfer and communication with devices V 1.9.1 New Features Updated embedded firmware versions for all products Add support and parameters for KeyStep firmware 1.1.0 V 1.9.0 New Features Microlab integration KeyLab MKII : added support of USB to CV out KeyLab MKII : added acceleration on knobs Keylab MKII : added support of MMC messages Keylab MKII : Midi notes can now be assigned to sustain, expression and auxiliary pedals Improvements Improved Firmware version detection for every device V1.8.1 New features Integration of Keylab88 MKII Fixes Fix MicroFreak Factory Bank 1.1 V1.8.0 New features Integration of Microfreak Integration of Arturia USB MIDI driver for Microfreak in Windows version, allows "multi-client" MIDI handling, for Microfreak only. Integration of 2 factory preset banks for the Microfreak Improvements Improved Firmware version detection for every device Fixes MatrixBrute : Presets name, type, and characteristics can now be edited in device's area MatrixBrute : No more failure when renaming projects Matrixbrute : Interval between projects now follows scroll position properly V1.7.5 Fixes Updated embedded firmware versions for all products Various Typos corrections V 1.7.4 New Features DrumBrute Impact added to the list of devices V 1.7.
10.10+	New Midi Control Center	16-Jan-2020	34.3 Mb	1.10.1.1411	MIDI Control Center V 1.10.1 New Features KeyLab Essential 88 integration Microfreak firmware 2.0.3 integration Added "Factory 2.0" presets bank for the Microfreak Added relative bend, scale, and root note settings for the Microfreak Updated embedded firmware versions for all products V 1.10.0 New Features Added MatrixBrute Factory 2.0 bank for MCC MatrixBrute 2.0 Firmware integration Catalina compatibility: Notarize macOs installer Added a modal popup when transfering preset or memories Improvements Various improvements for preset transfer and communication with devices V 1.9.1 New Features Updated embedded firmware versions for all products Add support and parameters for KeyStep firmware 1.1.0 V 1.9.0 New Features Microlab integration KeyLab MKII : added support of USB to CV out KeyLab MKII : added acceleration on knobs Keylab MKII : added support of MMC messages Keylab MKII : Midi notes can now be assigned to sustain, expression and auxiliary pedals Improvements Improved Firmware version detection for every device V1.8.1 New features Integration of Keylab88 MKII Fixes Fix MicroFreak Factory Bank 1.1 V1.8.0 New features Integration of Microfreak Integration of Arturia USB MIDI driver for Microfreak in Windows version, allows "multi-client" MIDI handling, for Microfreak only. Integration of 2 factory preset banks for the Microfreak Improvements Improved Firmware version detection for every device Fixes MatrixBrute : Presets name, type, and characteristics can now be edited in device's area MatrixBrute : No more failure when renaming projects Matrixbrute : Interval between projects now follows scroll position properly V1.7.5 Fixes Updated embedded firmware versions for all products Various Typos corrections V 1.7.4 New Features DrumBrute Impact added to the list of devices V 1.7.
10.10+	Midi Control Center	27-Nov-2019	34.2 Mb	1.10.0.1354	MIDI Control Center V 1.10.0 New Features Added MatrixBrute Factory 2.0 bank for MCC MatrixBrute 2.0 Firmware integration Catalina compatibility: Notarize macOs installer Added a modal popup when transfering preset or memories Improvements Various improvements for preset transfer and communication with devices V 1.9.1 New Features Updated embedded firmware versions for all products Add support and parameters for KeyStep firmware 1.1.0 V 1.9.0 New Features Microlab integration KeyLab MKII : added support of USB to CV out KeyLab MKII : added acceleration on knobs Keylab MKII : added support of MMC messages Keylab MKII : Midi notes can now be assigned to sustain, expression and auxiliary pedals Improvements Improved Firmware version detection for every device V1.8.1 New features Integration of Keylab88 MKII Fixes Fix MicroFreak Factory Bank 1.1 V1.8.0 New features Integration of Microfreak Integration of Arturia USB MIDI driver for Microfreak in Windows version, allows "multi-client" MIDI handling, for Microfreak only. Integration of 2 factory preset banks for the Microfreak Improvements Improved Firmware version detection for every device Fixes MatrixBrute : Presets name, type, and characteristics can now be edited in device's area MatrixBrute : No more failure when renaming projects Matrixbrute : Interval between projects now follows scroll position properly V1.7.5 Fixes Updated embedded firmware versions for all products Various Typos corrections V 1.7.4 New Features DrumBrute Impact added to the list of devices V 1.7.3 New Features KeyLab mkII added to the list of devices MCC will recall the previous display size on reopening Fixes MatrixBrute : Factory project is now well displayed on osx 10.13 V 1.7.1 New Features Integration of MiniBrute 2 & MiniBrute 2S V 1.7.0 New Features Integration of Keylab Essential Integration of BeatStep Pro 2.0 Integration of MiniBrute Integration of MicroBrute MiniLab mk2 firmware update now expects later releases Uninstall from ASC Manual is accessible from the MCC Fixes Various BeatStep Pro fixes MIDI Console now shows events even when Sync is off Various MIDI Console fixes V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
Win 7+	Midi Control Center	27-Nov-2019	25.9 Mb	1.10.0.1354	MIDI Control Center V 1.10.0 New Features Added MatrixBrute Factory 2.0 bank for MCC MatrixBrute 2.0 Firmware integration Catalina compatibility: Notarize macOs installer Added a modal popup when transfering preset or memories Improvements Various improvements for preset transfer and communication with devices V 1.9.1 New Features Updated embedded firmware versions for all products Add support and parameters for KeyStep firmware 1.1.0 V 1.9.0 New Features Microlab integration KeyLab MKII : added support of USB to CV out KeyLab MKII : added acceleration on knobs Keylab MKII : added support of MMC messages Keylab MKII : Midi notes can now be assigned to sustain, expression and auxiliary pedals Improvements Improved Firmware version detection for every device V1.8.1 New features Integration of Keylab88 MKII Fixes Fix MicroFreak Factory Bank 1.1 V1.8.0 New features Integration of Microfreak Integration of Arturia USB MIDI driver for Microfreak in Windows version, allows "multi-client" MIDI handling, for Microfreak only. Integration of 2 factory preset banks for the Microfreak Improvements Improved Firmware version detection for every device Fixes MatrixBrute : Presets name, type, and characteristics can now be edited in device's area MatrixBrute : No more failure when renaming projects Matrixbrute : Interval between projects now follows scroll position properly V1.7.5 Fixes Updated embedded firmware versions for all products Various Typos corrections V 1.7.4 New Features DrumBrute Impact added to the list of devices V 1.7.3 New Features KeyLab mkII added to the list of devices MCC will recall the previous display size on reopening Fixes MatrixBrute : Factory project is now well displayed on osx 10.13 V 1.7.1 New Features Integration of MiniBrute 2 & MiniBrute 2S V 1.7.0 New Features Integration of Keylab Essential Integration of BeatStep Pro 2.0 Integration of MiniBrute Integration of MicroBrute MiniLab mk2 firmware update now expects later releases Uninstall from ASC Manual is accessible from the MCC Fixes Various BeatStep Pro fixes MIDI Console now shows events even when Sync is off Various MIDI Console fixes V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
10.10+	Midi Control Center	29-Jul-2019	39.5 Mb	1.9.1.1186	MIDI Control Center V 1.9.1 New Features Updated embedded firmware versions for all products Add support and parameters for KeyStep firmware 1.1.0 V 1.9.0 New Features Microlab integration KeyLab MKII : added support of USB to CV out KeyLab MKII : added acceleration on knobs Keylab MKII : added support of MMC messages Keylab MKII : Midi notes can now be assigned to sustain, expression and auxiliary pedals Improvements Improved Firmware version detection for every device V1.8.1 New features Integration of Keylab88 MKII Fixes Fix MicroFreak Factory Bank 1.1 V1.8.0 New features Integration of Microfreak Integration of Arturia USB MIDI driver for Microfreak in Windows version, allows "multi-client" MIDI handling, for Microfreak only. Integration of 2 factory preset banks for the Microfreak Improvements Improved Firmware version detection for every device Fixes MatrixBrute : Presets name, type, and characteristics can now be edited in device's area MatrixBrute : No more failure when renaming projects Matrixbrute : Interval between projects now follows scroll position properly V1.7.5 Fixes Updated embedded firmware versions for all products Various Typos corrections V 1.7.4 New Features DrumBrute Impact added to the list of devices V 1.7.3 New Features KeyLab mkII added to the list of devices MCC will recall the previous display size on reopening Fixes MatrixBrute : Factory project is now well displayed on osx 10.13 V 1.7.1 New Features Integration of MiniBrute 2 & MiniBrute 2S V 1.7.0 New Features Integration of Keylab Essential Integration of BeatStep Pro 2.0 Integration of MiniBrute Integration of MicroBrute MiniLab mk2 firmware update now expects later releases Uninstall from ASC Manual is accessible from the MCC Fixes Various BeatStep Pro fixes MIDI Console now shows events even when Sync is off Various MIDI Console fixes V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
Win 7+	Midi Control Center	29-Jul-2019	25.2 Mb	1.9.1.1186	MIDI Control Center V 1.9.1 New Features Updated embedded firmware versions for all products Add support and parameters for KeyStep firmware 1.1.0 V 1.9.0 New Features Microlab integration KeyLab MKII : added support of USB to CV out KeyLab MKII : added acceleration on knobs Keylab MKII : added support of MMC messages Keylab MKII : Midi notes can now be assigned to sustain, expression and auxiliary pedals Improvements Improved Firmware version detection for every device V1.8.1 New features Integration of Keylab88 MKII Fixes Fix MicroFreak Factory Bank 1.1 V1.8.0 New features Integration of Microfreak Integration of Arturia USB MIDI driver for Microfreak in Windows version, allows "multi-client" MIDI handling, for Microfreak only. Integration of 2 factory preset banks for the Microfreak Improvements Improved Firmware version detection for every device Fixes MatrixBrute : Presets name, type, and characteristics can now be edited in device's area MatrixBrute : No more failure when renaming projects Matrixbrute : Interval between projects now follows scroll position properly V1.7.5 Fixes Updated embedded firmware versions for all products Various Typos corrections V 1.7.4 New Features DrumBrute Impact added to the list of devices V 1.7.3 New Features KeyLab mkII added to the list of devices MCC will recall the previous display size on reopening Fixes MatrixBrute : Factory project is now well displayed on osx 10.13 V 1.7.1 New Features Integration of MiniBrute 2 & MiniBrute 2S V 1.7.0 New Features Integration of Keylab Essential Integration of BeatStep Pro 2.0 Integration of MiniBrute Integration of MicroBrute MiniLab mk2 firmware update now expects later releases Uninstall from ASC Manual is accessible from the MCC Fixes Various BeatStep Pro fixes MIDI Console now shows events even when Sync is off Various MIDI Console fixes V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
10.10+	Midi Control Center	22-Jul-2019	39.1 Mb	1.9.0.1174	MIDI Control Center V 1.9.0 New Features Microlab integration KeyLab MKII : added support of USB to CV out KeyLab MKII : added acceleration on knobs Keylab MKII : added support of MMC messages Keylab MKII : Midi notes can now be assigned to sustain, expression and auxiliary pedals Improvements Improved Firmware version detection for every device V1.8.1 New features Integration of Keylab88 MKII Fixes Fix MicroFreak Factory Bank 1.1 V1.8.0 New features Integration of Microfreak Integration of Arturia USB MIDI driver for Microfreak in Windows version, allows "multi-client" MIDI handling, for Microfreak only. Integration of 2 factory preset banks for the Microfreak Improvements Improved Firmware version detection for every device Fixes MatrixBrute : Presets name, type, and characteristics can now be edited in device's area MatrixBrute : No more failure when renaming projects Matrixbrute : Interval between projects now follows scroll position properly V1.7.5 Fixes Updated embedded firmware versions for all products Various Typos corrections V 1.7.4 New Features DrumBrute Impact added to the list of devices V 1.7.3 New Features KeyLab mkII added to the list of devices MCC will recall the previous display size on reopening Fixes MatrixBrute : Factory project is now well displayed on osx 10.13 V 1.7.1 New Features Integration of MiniBrute 2 & MiniBrute 2S V 1.7.0 New Features Integration of Keylab Essential Integration of BeatStep Pro 2.0 Integration of MiniBrute Integration of MicroBrute MiniLab mk2 firmware update now expects later releases Uninstall from ASC Manual is accessible from the MCC Fixes Various BeatStep Pro fixes MIDI Console now shows events even when Sync is off Various MIDI Console fixes V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
Win 7+	Midi Control Center	22-Jul-2019	25.1 Mb	1.9.0.1174	MIDI Control Center V 1.9.0 New Features Microlab integration KeyLab MKII : added support of USB to CV out KeyLab MKII : added acceleration on knobs Keylab MKII : added support of MMC messages Keylab MKII : Midi notes can now be assigned to sustain, expression and auxiliary pedals Improvements Improved Firmware version detection for every device V1.8.1 New features Integration of Keylab88 MKII Fixes Fix MicroFreak Factory Bank 1.1 V1.8.0 New features Integration of Microfreak Integration of Arturia USB MIDI driver for Microfreak in Windows version, allows "multi-client" MIDI handling, for Microfreak only. Integration of 2 factory preset banks for the Microfreak Improvements Improved Firmware version detection for every device Fixes MatrixBrute : Presets name, type, and characteristics can now be edited in device's area MatrixBrute : No more failure when renaming projects Matrixbrute : Interval between projects now follows scroll position properly V1.7.5 Fixes Updated embedded firmware versions for all products Various Typos corrections V 1.7.4 New Features DrumBrute Impact added to the list of devices V 1.7.3 New Features KeyLab mkII added to the list of devices MCC will recall the previous display size on reopening Fixes MatrixBrute : Factory project is now well displayed on osx 10.13 V 1.7.1 New Features Integration of MiniBrute 2 & MiniBrute 2S V 1.7.0 New Features Integration of Keylab Essential Integration of BeatStep Pro 2.0 Integration of MiniBrute Integration of MicroBrute MiniLab mk2 firmware update now expects later releases Uninstall from ASC Manual is accessible from the MCC Fixes Various BeatStep Pro fixes MIDI Console now shows events even when Sync is off Various MIDI Console fixes V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
10.10+	Midi Control Center	19-Jun-2019	38.6 Mb	1.8.1.1122	MIDI Control Center V1.8.1 New features Integration of Keylab88 MKII Fixes Fix MicroFreak Factory Bank 1.1 V1.8.0 New features Integration of Microfreak Integration of Arturia USB MIDI driver for Microfreak in Windows version, allows "multi-client" MIDI handling, for Microfreak only. Integration of 2 factory preset banks for the Microfreak Improvements Improved Firmware version detection for every device Fixes MatrixBrute : Presets name, type, and characteristics can now be edited in device's area MatrixBrute : No more failure when renaming projects Matrixbrute : Interval between projects now follows scroll position properly V1.7.5 Fixes Updated embedded firmware versions for all products Various Typos corrections V 1.7.4 New Features DrumBrute Impact added to the list of devices V 1.7.3 New Features KeyLab mkII added to the list of devices MCC will recall the previous display size on reopening Fixes MatrixBrute : Factory project is now well displayed on osx 10.13 V 1.7.1 New Features Integration of MiniBrute 2 & MiniBrute 2S V 1.7.0 New Features Integration of Keylab Essential Integration of BeatStep Pro 2.0 Integration of MiniBrute Integration of MicroBrute MiniLab mk2 firmware update now expects later releases Uninstall from ASC Manual is accessible from the MCC Fixes Various BeatStep Pro fixes MIDI Console now shows events even when Sync is off Various MIDI Console fixes V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
Win 7+	Midi Control Center	19-Jun-2019	24.7 Mb	1.8.1.1122	MIDI Control Center V1.8.1 New features Integration of Keylab88 MKII Fixes Fix MicroFreak Factory Bank 1.1 V1.8.0 New features Integration of Microfreak Integration of Arturia USB MIDI driver for Microfreak in Windows version, allows "multi-client" MIDI handling, for Microfreak only. Integration of 2 factory preset banks for the Microfreak Improvements Improved Firmware version detection for every device Fixes MatrixBrute : Presets name, type, and characteristics can now be edited in device's area MatrixBrute : No more failure when renaming projects Matrixbrute : Interval between projects now follows scroll position properly V1.7.5 Fixes Updated embedded firmware versions for all products Various Typos corrections V 1.7.4 New Features DrumBrute Impact added to the list of devices V 1.7.3 New Features KeyLab mkII added to the list of devices MCC will recall the previous display size on reopening Fixes MatrixBrute : Factory project is now well displayed on osx 10.13 V 1.7.1 New Features Integration of MiniBrute 2 & MiniBrute 2S V 1.7.0 New Features Integration of Keylab Essential Integration of BeatStep Pro 2.0 Integration of MiniBrute Integration of MicroBrute MiniLab mk2 firmware update now expects later releases Uninstall from ASC Manual is accessible from the MCC Fixes Various BeatStep Pro fixes MIDI Console now shows events even when Sync is off Various MIDI Console fixes V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
10.10+	Midi Control Center	04-Apr-2019	38.6 Mb	1.8.0.1031	MIDI Control Center V1.8.0 New features Integration of Microfreak Integration of Arturia USB MIDI driver for Microfreak in Windows version, allows "multi-client" MIDI handling, for Microfreak only. Integration of 2 factory preset banks for the Microfreak Improvements Improved Firmware version detection for every device Fixes MatrixBrute : Presets name, type, and characteristics can now be edited in device's area MatrixBrute : No more failure when renaming projects Matrixbrute : Interval between projects now follows scroll position properly V1.7.5 Fixes Updated embedded firmware versions for all products Various Typos corrections V 1.7.4 New Features DrumBrute Impact added to the list of devices V 1.7.3 New Features KeyLab mkII added to the list of devices MCC will recall the previous display size on reopening Fixes MatrixBrute : Factory project is now well displayed on osx 10.13 V 1.7.1 New Features Integration of MiniBrute 2 & MiniBrute 2S V 1.7.0 New Features Integration of Keylab Essential Integration of BeatStep Pro 2.0 Integration of MiniBrute Integration of MicroBrute MiniLab mk2 firmware update now expects later releases Uninstall from ASC Manual is accessible from the MCC Fixes Various BeatStep Pro fixes MIDI Console now shows events even when Sync is off Various MIDI Console fixes V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
Win 7+	Midi Control Center	04-Apr-2019	24.7 Mb	1.8.0.1031	MIDI Control Center V1.8.0 New features Integration of Microfreak Integration of Arturia USB MIDI driver for Microfreak in Windows version, allows "multi-client" MIDI handling, for Microfreak only. Integration of 2 factory preset banks for the Microfreak Improvements Improved Firmware version detection for every device Fixes MatrixBrute : Presets name, type, and characteristics can now be edited in device's area MatrixBrute : No more failure when renaming projects Matrixbrute : Interval between projects now follows scroll position properly V1.7.5 Fixes Updated embedded firmware versions for all products Various Typos corrections V 1.7.4 New Features DrumBrute Impact added to the list of devices V 1.7.3 New Features KeyLab mkII added to the list of devices MCC will recall the previous display size on reopening Fixes MatrixBrute : Factory project is now well displayed on osx 10.13 V 1.7.1 New Features Integration of MiniBrute 2 & MiniBrute 2S V 1.7.0 New Features Integration of Keylab Essential Integration of BeatStep Pro 2.0 Integration of MiniBrute Integration of MicroBrute MiniLab mk2 firmware update now expects later releases Uninstall from ASC Manual is accessible from the MCC Fixes Various BeatStep Pro fixes MIDI Console now shows events even when Sync is off Various MIDI Console fixes V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
10.10+	Midi Control Center	10-Oct-2018	42.3 Mb	1.7.5.812	MIDI Control Center V1.7.5 Fixes Updated embedded firmware versions for all products Various Typos corrections V 1.7.4 New Features DrumBrute Impact added to the list of devices V 1.7.3 New Features KeyLab mkII added to the list of devices MCC will recall the previous display size on reopening Fixes MatrixBrute : Factory project is now well displayed on osx 10.13 V 1.7.1 New Features Integration of MiniBrute 2 & MiniBrute 2S V 1.7.0 New Features Integration of Keylab Essential Integration of BeatStep Pro 2.0 Integration of MiniBrute Integration of MicroBrute MiniLab mk2 firmware update now expects later releases Uninstall from ASC Manual is accessible from the MCC Fixes Various BeatStep Pro fixes MIDI Console now shows events even when Sync is off Various MIDI Console fixes V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
Win 7+	Midi Control Center	10-Oct-2018	22.2 Mb	1.7.5.812	MIDI Control Center V1.7.5 Fixes Updated embedded firmware versions for all products Various Typos corrections V 1.7.4 New Features DrumBrute Impact added to the list of devices V 1.7.3 New Features KeyLab mkII added to the list of devices MCC will recall the previous display size on reopening Fixes MatrixBrute : Factory project is now well displayed on osx 10.13 V 1.7.1 New Features Integration of MiniBrute 2 & MiniBrute 2S V 1.7.0 New Features Integration of Keylab Essential Integration of BeatStep Pro 2.0 Integration of MiniBrute Integration of MicroBrute MiniLab mk2 firmware update now expects later releases Uninstall from ASC Manual is accessible from the MCC Fixes Various BeatStep Pro fixes MIDI Console now shows events even when Sync is off Various MIDI Console fixes V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
10.10+	Midi Control Center	04-Jul-2018	42.3 Mb	1.7.4.701	MIDI Control Center V 1.7.4 New Features DrumBrute Impact added to the list of devices V 1.7.3 New Features KeyLab mkII added to the list of devices MCC will recall the previous display size on reopening Fixes MatrixBrute : Factory project is now well displayed on osx 10.13 V 1.7.1 New Features Integration of MiniBrute 2 & MiniBrute 2S V 1.7.0 New Features Integration of Keylab Essential Integration of BeatStep Pro 2.0 Integration of MiniBrute Integration of MicroBrute MiniLab mk2 firmware update now expects later releases Uninstall from ASC Manual is accessible from the MCC Fixes Various BeatStep Pro fixes MIDI Console now shows events even when Sync is off Various MIDI Console fixes V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
Win 7+	Midi Control Center	04-Jul-2018	22.2 Mb	1.7.4.701	MIDI Control Center V 1.7.4 New Features DrumBrute Impact added to the list of devices V 1.7.3 New Features KeyLab mkII added to the list of devices MCC will recall the previous display size on reopening Fixes MatrixBrute : Factory project is now well displayed on osx 10.13 V 1.7.1 New Features Integration of MiniBrute 2 & MiniBrute 2S V 1.7.0 New Features Integration of Keylab Essential Integration of BeatStep Pro 2.0 Integration of MiniBrute Integration of MicroBrute MiniLab mk2 firmware update now expects later releases Uninstall from ASC Manual is accessible from the MCC Fixes Various BeatStep Pro fixes MIDI Console now shows events even when Sync is off Various MIDI Console fixes V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
10.10+	Midi Control Center	15-Jun-2018	40.7 Mb	1.7.3.678	MIDI Control Center V 1.7.3 New Features KeyLab mkII added to the list of devices MCC will recall the previous display size on reopening Fixes MatrixBrute : Factory project is now well displayed on osx 10.13 V 1.7.1 New Features Integration of MiniBrute 2 & MiniBrute 2S V 1.7.0 New Features Integration of Keylab Essential Integration of BeatStep Pro 2.0 Integration of MiniBrute Integration of MicroBrute MiniLab mk2 firmware update now expects later releases Uninstall from ASC Manual is accessible from the MCC Fixes Various BeatStep Pro fixes MIDI Console now shows events even when Sync is off Various MIDI Console fixes V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
Win 7+	Midi Control Center	15-Jun-2018	20.7 Mb	1.7.3.678	MIDI Control Center V 1.7.3 New Features KeyLab mkII added to the list of devices MCC will recall the previous display size on reopening Fixes MatrixBrute : Factory project is now well displayed on osx 10.13 V 1.7.1 New Features Integration of MiniBrute 2 & MiniBrute 2S V 1.7.0 New Features Integration of Keylab Essential Integration of BeatStep Pro 2.0 Integration of MiniBrute Integration of MicroBrute MiniLab mk2 firmware update now expects later releases Uninstall from ASC Manual is accessible from the MCC Fixes Various BeatStep Pro fixes MIDI Console now shows events even when Sync is off Various MIDI Console fixes V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
10.8+	Midi Control Center	05-Feb-2018	38.4 Mb	1.7.1.506	MIDI Control Center V 1.7.1 New Features Integration of MiniBrute 2 & MiniBrute 2S V 1.7.0 New Features Integration of Keylab Essential Integration of BeatStep Pro 2.0 Integration of MiniBrute Integration of MicroBrute MiniLab mk2 firmware update now expects later releases Uninstall from ASC Manual is accessible from the MCC Fixes Various BeatStep Pro fixes MIDI Console now shows events even when Sync is off Various MIDI Console fixes V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
Win 7+	Midi Control Center	05-Feb-2018	19.4 Mb	1.7.1.506	MIDI Control Center V 1.7.1 New Features Integration of MiniBrute 2 & MiniBrute 2S V 1.7.0 New Features Integration of Keylab Essential Integration of BeatStep Pro 2.0 Integration of MiniBrute Integration of MicroBrute MiniLab mk2 firmware update now expects later releases Uninstall from ASC Manual is accessible from the MCC Fixes Various BeatStep Pro fixes MIDI Console now shows events even when Sync is off Various MIDI Console fixes V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
10.8+	Midi Control Center	23-Jun-2017	35.7 Mb	1.7.0.217	MIDI Control Center V 1.7.0 New Features Integration of Keylab Essential Integration of BeatStep Pro 2.0 Integration of MiniBrute Integration of MicroBrute MiniLab mk2 firmware update now expects later releases Uninstall from ASC Manual is accessible from the MCC Fixes Various BeatStep Pro fixes MIDI Console now shows events even when Sync is off Various MIDI Console fixes V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
Win 7+	Midi Control Center	23-Jun-2017	17.3 Mb	1.7.0.217	MIDI Control Center V 1.7.0 New Features Integration of Keylab Essential Integration of BeatStep Pro 2.0 Integration of MiniBrute Integration of MicroBrute MiniLab mk2 firmware update now expects later releases Uninstall from ASC Manual is accessible from the MCC Fixes Various BeatStep Pro fixes MIDI Console now shows events even when Sync is off Various MIDI Console fixes V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
10.8+	Midi Control Center	24-Mar-2017	32.9 Mb	1.6.2.85	MIDI Control Center V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
Win 7+	Midi Control Center	24-Mar-2017	14.8 Mb	1.6.2.85	MIDI Control Center V 1.6.2 New Features MatrixBrute : Added VCO 1 & 2 CV 0v Offset MatrixBrute : Added Lower Part MIDI Channel MatrixBrute : Improved Sync Clock In/Out Settings Fixes MatrixBrute : Preset info properly loaded when selecting MatrixBrute in the list of devices V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
Win 7+	Midi Control Center	03-Feb-2017	19.1 Mb	1.6.1.14	MIDI Control Center V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
10.8+	Midi Control Center	03-Feb-2017	37.6 Mb	1.6.1.14	MIDI Control Center V 1.6.1 New Features Drumbrute : added Roller/Looper section Improvements Improve tooltip message when Sync not available Failed to open device : a better workflow/popup is now provided Fixes Drumbrute : "All" has been removed from global midi channel V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
10.8+	Midi Control Center	21-Dec-2016	37.6 Mb	1.6.0.921	MIDI Control Center V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
Win 7+	Midi Control Center	21-Dec-2016	19.2 Mb	1.6.0.921	MIDI Control Center V 1.6.0 New Features MatrixBrute added to the list of devices Fixes Updated Minilab MK2 firmware for offline update V 1.5.1 Fixes MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
10.8+	Midi Control Center	22-Nov-2016	37 Mb	1.5.1.882	MIDI Control Center V 1.5.1 MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
Win 7+	Midi Control Center	22-Nov-2016	18.7 Mb	1.5.1.882	MIDI Control Center V 1.5.1 MIDI Control Center properly handles firmware updates when the computer is offline V 1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V 1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes Beatstep : wrong embedded FW V 1.3.1 New Features Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V 1.3.0 - KeyStep New Features KeyStep added to the list of devices KeyLab88 : velocity curves Fixes BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V 1.2.2 New Features BeatStep pro : Add Wait To Load Pattern function Fixes BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V 1.2.1 Fixes BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V 1.2.0 - BeatStepPro New Features Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V 1.1.0 - BeatStep New Features BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V 1.0.1 Fixes Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
10.8+	Midi Control Center	15-Nov-2016	37 Mb	1.5.0.868	MIDI Control Center V1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes : After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes: Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V1.3.2 Fixes: Beatstep : wrong embedded FW V1.3.1 New Features: Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes: Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V1.3.0 - KeyStep New Features: KeyStep added to the list of devices KeyLab88 : velocity curves Fixes: BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V1.2.2 New Features: BeatStep pro : Add Wait To Load Pattern function Fixes: BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V1.2.1 Fixes: BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V1.2.0 - BeatStepPro New Features: Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V1.1.0 - BeatStep New Features: BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V1.0.1 Fixes: Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
Win 7+	Midi Control Center	15-Nov-2016	18.8 Mb	1.5.0.868	MIDI Control Center V1.5.0 - Minilab-mkII New Features Minilab MkII added to the list of devices Fixes : After a firmware update, MCC displays properly device settings No more crashes if drumbrute is disconnected while transferring data V1.4.0 - DrumBrute New Features DrumBrute added to the list of devices Fixes: Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V1.3.2 Fixes: Beatstep : wrong embedded FW V1.3.1 New Features: Keystep : add courbe "soft" for aftertouch issue Keystep : set popup to update fw if version smaller Keystep : update fw reboot message Fixes: Auto-Update : Updater tool is missing mouseUp/mouseDrag bad handled on Mac BeatStep Pro : update FW indicator issue Keylab 88 : missing value for pad velocity curve Keylab 88 : Snap button as KBD memory - memory number default value is wrong V1.3.0 - KeyStep New Features: KeyStep added to the list of devices KeyLab88 : velocity curves Fixes: BeatStep pro : Crash when editing step Importing device settings, impossible to find the file to import User template(s) missing 's' Button configuration no more available Limit zoom out in piano roll and drum roll V1.2.2 New Features: BeatStep pro : Add Wait To Load Pattern function Fixes: BeatStep pro : wrong global settings at opening BeatStep pro : Wrong param id Seq2 Hz/V 1V MIDI Note BeatStep pro : New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) BeatStep pro : "Device not connected" pop up when BSP not connected V1.2.1 Fixes: BeatStep pro : Remove Sync feature on BSP Update FW recalling update popup BeatStep pro : set drum map range to [0,127] BeatStep pro : inversion Seq1 Gate et Seq 2 Pitch KeyLab 88 : update (transpose, bank MSB for pads, sustain pedal threshold) Minimal Required version popup : 1.1.0.4 for KL88, 1.1.2.0 for BSP V1.2.0 - BeatStepPro New Features: Auto-Update MCC Automatic download of latest firmware HW Test interface BeatStepPro support : piano roll support bulks partial transfert of parameters from computer to device device global parameters V1.1.0 - BeatStep New Features: BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center. V1.0.1 Fixes: Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
Win 7+	Midi Control Center	30-Sep-2016	18 Mb	1.4.0.790	MIDI Control Center V 1.4.0 Fixes: Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues DrumBrute added to the list of devices Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes: 128455 : Beatstep : wrong embedded FW
10.8+	Midi Control Center	30-Sep-2016	36.2 Mb	1.4.0.790	MIDI Control Center V 1.4.0 Fixes: Improved memory handling for MiniLab - Sync or Working Memory manipulations created issues DrumBrute added to the list of devices Updated BeatStep firmware for offline update Devices are now not editable when in firmware update mode It is now possible to read the connected device's firmware version after an update of the MCC V 1.3.2 Fixes: 128455 : Beatstep : wrong embedded FW
10.8+	Midi Control Center	20-Jul-2016	31.7 Mb	1.3.2.673	MIDI Control Center V 1.3.2 Fixes: Beatstep : Firmware update now selects the right firmware version
Win 7+	Midi Control Center	20-Jul-2016	16.1 Mb	1.3.2.673	MIDI Control Center V 1.3.2 Fixes: Beatstep : Firmware update now selects the right firmware version
Win 7+	Midi Control Center	30-Jun-2016	16.3 Mb	1.3.1.667	MIDI Control Center V 1.3.1 New Features For Keystep add "soft" curve selection for aftertouch response Bugfixes Mouse drag is now properly handled on OSX Available firmware update information is now properly displayed For KeyLab 88, "Constant 127" Pad velocity curve is now available
10.8+	Midi Control Center	30-Jun-2016	31.7 Mb	1.3.1.667	MIDI Control Center V 1.3.1 New Features For Keystep add "soft" curve selection for aftertouch response Bugfixes Mouse drag is now properly handled on OSX Available firmware update information is now properly displayed For KeyLab 88, "Constant 127" Pad velocity curve is now available
Win 7+	Midi Control Center	30-Mar-2016	15.7 Mb	1.3.0.562	MIDI Control Center V 1.3.0 New Features KeyStep integration The user can edit custom velocity curves for KeyLab 88 Improved readability on global settings Fixed Bugs No more crash while editing a sequence step with BeatStep Pro No more error message while updating the firmware Other minor fixes on UI
10.8+	Midi Control Center	30-Mar-2016	25.9 Mb	1.3.0.562	MIDI Control Center V 1.3.0 New Features KeyStep integration The user can edit custom velocity curves for KeyLab 88 Improved readability on global settings Fixed Bugs No more crash while editing a sequence step with BeatStep Pro No more error message while updating the firmware Other minor fixes on UI
10.7+	MIDI Control Center Unified	20-Nov-2015	20.1 Mb	1.2.2.429	MIDI Control Center V 1.2.2.429 Features: BSP : Add Wait To Load Pattern function Fixes: [BSP] No more wrong global settings at opening [BSP] Correction on wrong Parameter Id Seq2 Hz/V 1V MIDI Note [BSP] New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) [BSP] Pop up ìDevice not connectedî is suppressed when BSP is not connected
Win 7+	MIDI Control Center Unified	20-Nov-2015	10.9 Mb	1.2.2.429	MIDI Control Center V 1.2.2.429 Features: BSP : Add Wait To Load Pattern function Fixes: [BSP] No more wrong global settings at opening [BSP] Correction on wrong Parameter Id Seq2 Hz/V 1V MIDI Note [BSP] New factory preset (MIDI&USB, Wait to load ON, Pas to Midi Channel USER) [BSP] Pop up ìDevice not connectedî is suppressed when BSP is not connected
10.7+	MIDI Control Center Unified	23-Sep-2015	20.1 Mb	1.2.1	MIDI Control Center V 1.2.1 Improvements: BeatStep Pro Sync function was replaced by drag and drop between device memories and local templates. Drag and drop Controller Map, Sequences, Drum Sequences separately from local templates to BeatStep Pro. Set drum map range to [0,127] for BeatStep Pro New features from KeyLab 88 version 1.1 are accessible Bug Fixes: BeatStep Pro Sequencer 1 Gate type and Sequencer 2 CV type were inverted
Win 7+	MIDI Control Center Unified	23-Sep-2015	10.9 Mb	1.2.1	MIDI Control Center V 1.2.1 Improvements: BeatStep Pro Sync function was replaced by drag and drop between device memories and local templates. Drag and drop Controller Map, Sequences, Drum Sequences separately from local templates to BeatStep Pro. Set drum map range to [0,127] for BeatStep Pro New features from KeyLab 88 version 1.1 are accessible Bug Fixes: BeatStep Pro Sequencer 1 Gate type and Sequencer 2 CV type were inverted
10.7+	MIDI Control Center Unified	01-Jul-2015	20 Mb	1.2.0.301	MIDI Control Center V 1.2.0.301 New features Full support of BeatStep Pro (firmware version V1.1.0.3)
Win 7+	MIDI Control Center Unified	01-Jul-2015	10.9 Mb	1.2.0.301	MIDI Control Center V 1.2.0.301 New features Full support of BeatStep Pro (firmware version V1.1.0.3)
10.7+	MIDI Control Center Unified	19-Mar-2014	12.4 Mb	1.1	MIDI Control Center V 1.1.0 Features: BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center.
Win 7+	MIDI Control Center Unified	19-Mar-2014	9.3 Mb	1.1	MIDI Control Center V 1.1.0 Features: BeatStep support. Edit your sequences and user scales directly in the MIDI Control Center.
10.7+	MIDI Control Center Unified	21-Jan-2014	10.4 Mb	1.0	MIDI Control Center V 1.0 rc1 New Features: The firmware revision of you device is now displayed directly under the Device name. Clicking on it will open the Firmware Upgrade window (equivalent to going in the menu Device>Firmware Upgrade...) Bug Fixes: Fixed a bug where the Save button would stay disabled after changing a slider value Importing a template would sometimes change the selection in the Templates list. This is no longer the case. There is now a confirmation when deleting a template. Moreover, you can now press the 'Delete' key to quickly delete a template. V 1.0 beta Compatibility. This version supports Mac OSX 10.7 and higher, and Windows 7 and Windows 8. Features: The KeyLab's firmware update is now possible. Firmware files are available on the website. SparkLE and Spark can be updated as well. The firmware files will be available on the website at release. Misc: In the Default Keylab template, the transport buttons now send MMC messages (to reflect an upcoming firmware update) V 0.9.1 Compatibility. *This version supports Mac OSX 10.7 and higher, and Windows 7 and Windows 8. Features: Firmware upgrade is now possible for the MiniLab owners. You can access it from the Device menu. You will need to download the firmware files from the MiniLab resource page on the Arturia website. The Factory controller has a new global parameter, Knob Mode, allowing to switch between Absolute and Relative. Fixes: A window positionning problem when launching the application is fixed. Some labels are corrected.
Win 7+	MIDI Control Center Unified	21-Jan-2014	7.5 Mb	1.0	MIDI Control Center V 1.0 rc1 New Features: The firmware revision of you device is now displayed directly under the Device name. Clicking on it will open the Firmware Upgrade window (equivalent to going in the menu Device>Firmware Upgrade...) Bug Fixes: Fixed a bug where the Save button would stay disabled after changing a slider value Importing a template would sometimes change the selection in the Templates list. This is no longer the case. There is now a confirmation when deleting a template. Moreover, you can now press the 'Delete' key to quickly delete a template. V 1.0 beta Compatibility. This version supports Mac OSX 10.7 and higher, and Windows 7 and Windows 8. Features: The KeyLab's firmware update is now possible. Firmware files are available on the website. SparkLE and Spark can be updated as well. The firmware files will be available on the website at release. Misc: In the Default Keylab template, the transport buttons now send MMC messages (to reflect an upcoming firmware update) V 0.9.1 Compatibility. *This version supports Mac OSX 10.7 and higher, and Windows 7 and Windows 8. Features: Firmware upgrade is now possible for the MiniLab owners. You can access it from the Device menu. You will need to download the firmware files from the MiniLab resource page on the Arturia website. The Factory controller has a new global parameter, Knob Mode, allowing to switch between Absolute and Relative. Fixes: A window positionning problem when launching the application is fixed. Some labels are corrected.
10.7+	MIDI Control Center Unified	21-Jan-2014	11 Mb	1.0.1	MIDI Control Center V 1.0.1 Fixes: Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.
Win 7+	MIDI Control Center Unified	21-Jan-2014	7.9 Mb	1.0.1	MIDI Control Center V 1.0.1 Fixes: Mac 10.9 and Windows 8: Some devices were not properly seen as connected or the communication failed. If you experienced this bug on Mac 10.9, you might have to open Audio MIDI Setup and remove the MIDI Devices that had this problem.

MANUALS

Manual	Date	Size	Version
New Midi Control Center Spanish Manual	15-Jan-2018	1.8 Mb	1.0
New Midi Control Center Japanese Manual	07-Sep-2017	16 Mb	1.0.0
New Midi Control Center French Manual	07-Sep-2017	1.8 Mb	1.0.0
New Midi Control Center English Manual	21-Jun-2017	1.8 Mb	1.0

BeatStep

Compact Control PowerHouse

Downloads & manuals

BeatStep firmware

V 1.2.0.3

New features:

Improvements:

Bug fixes:

V 1.1.0.0

New Features

Bug Fixes

BeatStep firmware

V 1.2.0.3

New features:

Improvements:

Bug fixes:

V 1.1.0.0

New Features

Bug Fixes

BeatStep firmware

V 1.2.0.3

New features:

Improvements:

Bug fixes:

V 1.1.0.0

New Features

Bug Fixes

BeatStep firmware

V 1.1.0.0

New Features

Bug Fixes

BeatStep firmware

V 1.1.0.0

New Features

Bug Fixes

MIDI Control Center

V 1.10.1

New Features

V 1.10.0

New Features

Improvements

V 1.9.1

New Features

V 1.9.0

New Features

Improvements

V1.8.1

New features

Fixes

V1.8.0

New features

Improvements

Fixes

V1.7.5

Fixes

V 1.7.4

New Features

V 1.7.

MIDI Control Center

V 1.10.1

New Features

V 1.10.0

New Features

Improvements

V 1.9.1

New Features

V 1.9.0

New Features

Improvements

V1.8.1

New features

Fixes

V1.8.0

New features

Improvements

Fixes

V1.7.5

Fixes

V 1.7.4

New Features